2024 John Deere 2 Series 2025R

MoreLess
Limited Time Offer!

Selling Price -INVOICE - Call for quote!

2024 John Deere 2 Series 2025R

  • Standard LED headlights and fender lights
  • Hydro transmission with TwinTouch™ pedals for ease of use
  • AutoConnect™ mid-mower deck can be installed or removed in less than 5 minutes

Features may include:

Key features of the 2025R Tractor

ENGINE

  • Updated isolated Yanmar® TNV Clean & Silent Diesel Engine
  • Meets Tier 4-emission standards
  • Engine features lower levels of exhaust and emissions
  • Isolated engine for quieter operation
  • 24.2 gross hp - 18 PTO hp (5.8 percent increase in PTO hp over the 4110 Tractor)
  • As per 97/68/EC ISO @ rated speed.
POWERTRAIN
  • Standard HST transmission with Twin Touch™ foot pedals
  • Allows for increased performance
  • Larger tires
HYDRAULICS
  • Standard dual mid-selective control valve with integrated loader joystick
  • Two options for raising and lowering the mid-mount mower deck
  • Standard mechanical lift system—uses 3-point hitch to raise and lower mower deck
OPERATOR STATION AND CONTROLS
  • Ag tractor family styling
  • One-piece hood design
  • Updated instrument panel, dash, and throttle design
  • Molded foot deck
  • Standard folding rollover protective structure (ROPS)
  • Standard mid rockshaft with mower deck height adjustment
IMPLEMENTS
  • H130 Loaders
  • Commonality of loaders and rear implements between 2025R and 2032R
  • Updated drive-over deck with the stow-and-go feature
STANDARD EQUIPMENT FOR THE 2025R TRACTOR
  • Folding ROPS
  • Dual mid-selective control valve with integrated loader joystick control
  • Power steering
  • Four-wheel drive
  • Mid PTO
  • Wet-disk brakes
  • Cruise control

Yanmar is a U.S.-registered trademark of Yanmar Company Limited.

Yanmar® diesel engine

Power is provided by a durable and efficient high-torque 3-cylinder Yanmar TNV Series diesel engine.

This series of engines was developed to meet environmental requirements for Tier 4 (2025R) emission requirements by featuring lower levels of both exhaust and emissions.

As per 97/68/EC ISO at rated speed.

Yanmar TNV Series engine offers these:
  • Economical cast-in block cylinder design for good cooling and long life
  • Indirect fuel injection on the 2025R uses a pre-combustion chamber to give the engine a smooth and quiet operation
  • Direct fuel injection on the 2032R injects fuel on top of the pistons and allows for more efficient combustion and fuel economy
  • Aluminum alloy piston with built-in steel struts are lightweight to reduce connection rod bearing loads and provide good heat transfer characteristics
  • Design permits tighter tolerances and neutralizes expansion of the piston, thereby reducing blow-by gas and generating less noise from the piston slap
  • Higher top rings on the piston and a thinner head gasket greatly reduces the volume of unburned waste gases and increases combustion efficiency
  • Timing gear teeth have a roll-off profile giving almost no clash, no noise, and no backlash
  • Special flywheel flange seals flywheel air turbulence noise inside the flywheel housing
  • High-torque reserve provides plenty of power under heavy load yet retains excellent fuel economy
  • Fuel filter with replaceable element
  • 2024
  • John Deere
  • 2 Series
  • 2025R
  • Compact
  • Model: 3TNV80F-NCJT
  • SAE J1995 rated power: 23.9 hp (17.8 kW) / 3200 rpm at 24.2 PS
  • Yanmar®
  • 3200 rpm
  • Natural
  • Final Tier 4
  • 77 cu in. (1.267 L)
  • Three | Cast-in-block
  • 3.2 in (80 mm)
  • 3.3 in. (84 mm)
  • Pressurized
  • Water pump
  • Dual element
  • At rated speed: 39.1 lb-ft (53.1 Nm)
  • Power take-off (PTO) power: 17.2 hp (12.8 kW) | Rear - 540 rpm / Mid - 2100 rpm
  • Indirect injection
  • Diesel
  • 23.1:01
  • Indirect injection
  • Hydrostatic - two range
  • Spur gear
  • Power steering
  • Wet disk
  • Wet disk
  • R3 Turf: 23x8.50-12 / R3 Radial: 220/55-R12 / R4 Industrial: 23x8.50-12
  • R3 Turf: 12-16.5 / R3 Radial: 280/70 R16 / R4 Industrial: 12-16.5
  • 500 CCA
  • 40 amp
  • Starter size: 1.6 hp (1.2 kW)
  • Open center | Remote control valves available: Two
  • Steering: 3.5 gpm (13.4 L/min) / 3.5 gpm (13.25 L/min) | Implement: 3.5 gpm (13.4 L/min) / 3.5 gpm (13.25 L/min) / 7.0 gpm (26.5 L/min)
  • Gear
  • 1987 psi (137 bar)
  • Limited Category 1
  • 63 in. (1600 mm)
  • Without brakes: 8.2 ft (2.51 m)
  • 5.39 gal. (20.4 L)
  • 1349 lb (612 kg)
  • 2425 lb (1100 kg)
  • 24-in. behind link arms: 915 lb (415 kg)
  • Draft control sensing: Position control | Control: Independent | Platform - flat/straddle: Three-piece semi flat | Gear shift location - console/floor: Left-hand side
  • Open station: 1872 lb (849 kg) / Cab: 2392 lb ( 1085 kg)
  •  Calculation is estimate only.
  •  
  •  
  •  
  •  
  •  
  •  
  •  Quotes are estimates only, actual rate may vary slightly.
  •  One-Way toll road charges will be the responsibility of the customer.
  •  Additional fees and/or duties may apply to International and non-continental US shipping requests.
  • $27,068.00
  • Tunkhannock
  • New
  • 52039
  • 2024
  • John Deere
  • 2 Series 2025R
  • Model: 3TNV80F-NCJT
  • Hydrostatic - two range
  • Diesel
  • Available
Advertised pricing excludes applicable taxes title and licensing, dealer set up, destination, reconditioning and are subject to change without notice. Pricing may exclude any added parts, accessories or installation unless otherwise noted. Sale prices include all applicable offers. Not all options listed available on pre-owned models. Contact dealer for details.